Any C-50 C-60 C-70 Chev

Greasey Hand · Posted: Wed Sep 17, 2008 5:01 am Post subject: Any C-50 C-60 C-70 Chev

Looking for a parts truck in the 67 to 83 in MN
dont need it to run. Could be in other states close by. Realy need the flywheel for this harvest season, 366 motor.

too far · Guest Report to Moderator

Too bad Eastern MI is too far, I'd sell you my 366/5speed wet disc brake under CDL C65 cab/chassis cheap.

Seriously, doen't the 366 use the dame flywheel as 396/402/427? The large clutch version ought to be reasonable from Rock Auto parts.

Bob · Posted: Wed Sep 17, 2008 7:01 am Post subject: Re: Any C-50 C-60 C-70 Chev

Have you tried Lucken's Truck Salvage in Winger?

Also, an auto parts store SHOULD be able to get you an aftermarket replacement flywheel, probably for less than you think. And you get out of driving to get it, or paying freight, and it won't need to be resurfaced.

Greasey Hand · Posted: Wed Sep 17, 2008 12:56 pm Post subject: Re: Any C-50 C-60 C-70 Chev

There are no Rock Auto Parts stores in MN.
Never seen one.
I would like to see your truck, Does it run & what shape is it in & $$.
Is there a way to E Mail through this sight?
I checked for them to send me an E Mail about your truck.

Wheat Farmer · Posted: Thu Sep 18, 2008 5:17 am Post subject: Re: Any C-50 C-60 C-70 Chev

I have a 1963 C-60 setting in Deuel County NE, But not sure of the Engine Size (V Cool

, 45,000 miles, runs good. 4 speed 2 speed axle. Rear dump. steel box. More pictures available

Greasey Hand · Posted: Thu Sep 18, 2008 1:44 pm Post subject: Re: Any C-50 C-60 C-70 Chev

Wheat Farmer:

If its a V-8 it might be a 327 motor.
Send me an E Mail on price.
Thanks. fisherman@cmgate.com

Greasey Hand · Posted: Thu Sep 18, 2008 1:50 pm Post subject: Re: Any C-50 C-60 C-70 Chev

Bob:

I tried to get a flywheel from napa, city parts, Orileys, auto value. All said no.
Warhouse dont have them & no price on them.

Greasey Hand · Posted: Thu Sep 18, 2008 1:55 pm Post subject: Re: Any C-50 C-60 C-70 Chev

to far

My E is ^

ericlb · Posted: Fri Sep 19, 2008 2:57 am Post subject: Re: Any C-50 C-60 C-70 Chev

did these parts stores have kids [ under 25 or 30] in them using computers?, i just bought a new flywheel for a small block '83 chevy 1 ton, carquest had it in stock, and said he could get any common flywheel for a big 3 made engine overnight,[ the parts guy was pushing 70, and looked it up in a book] he knew his stuff, the flywheel is available look for a carquest or napa with old men in it that look like they grew odl in the store

Dan Hamill · Guest Report to Moderator

ericlb is right on the money in regards to the youngsters in the parts stores. We had a Big A store here for years owned by an older fellow from MN who could get anything you needed, and quote the part # most of the time. He retired, the store became CarQuest, kids took over, now you can get mud flaps, running boards, tailgate protecters, chrome pipes, but no parts.

Dogpile searcher · Guest Report to Moderator

www.dogpile.com, search on 366 flywheel, found several, $150-250 + shipping.

Greasey Hand · Posted: Sat Sep 27, 2008 5:09 am Post subject: Re: Any C-50 C-60 C-70 Chev

I found a good flywheel & pressure plate with the clutch.
The clutch is a button clutch, Never seen one used on a truck befor.
On tractors yes.
Are they better than a regular clutch a truck?
This is a 3 button clutch like new.
The bowel pin is gone from the crank end for the flywheel.
Are these still avalable from GM?
Or do any of you fellows have one?
When I get the dowel pin I can put the clutch assy in there.
I had to get a new PTO, That was spendy!!
It will be here in a few days.